eLoggerTM V4 - the Easiest Way to Monitor your Model's Power System!
New! Whether you’re into Electric
Model Planes, Helis, Cars, Boats or other models, you need to know how
your electric power system performs under actual operating
conditions. The eLogger is the product you need to monitor your LiPo, A123 or any other electric power system.
Here are a few of the enhancements with our new eLogger V4 (click here for more details):
High speed logging at up to 50Hz (increased from 10Hz).
Sixteen times the logging capacity of the standard eLogger V3. Typically logs all available sensors for about four hours, at 10Hz.
Voltage logging increased to 80 volts maximum.
The eLogger system comes with everything you need to log, analyse, and graph mAH, Current, Wattage, Voltage and throttle position, right out of the box. And, your eLogger is tremendously expandable, by adding additional sensors (shown below).
Why should I choose the Eagle Tree eLogger?
Some ESC manufacturers are adding data logging to their products. However, these logging capabilities are limited, have very short logging times at high sample rates, and few if any additional sensors are available. While these built-in solutions may "whet your appetite" for data, our eLogger and its incredible array of sensors and powerful software will let you measure virtually anything you will ever need.
Also, investing in logging add-ons that are tied to a particular ESC means that the investment is only good as long as you use that ESC. Eagle Tree telemetry is portable across any ESC brand/model.
Finally, while the ESC manufacturers and others may lose interest in their logging capabilities if they don't sell well, you can rest assured that Eagle Tree will continue to enhance and expand our eLogger with additional features and sensors. Data is all we do!
PowerPanel LCD Display - a Gas Gauge for your Pack!
Now you can connect our PowerPanel lightweight LCD Display module to your eLogger!
This ultra thin LCD
display connects to the eLogger with the included 11" data cable, and lets you get your max
and live data displayed without a PC, just like the heavier,
non-logging WattMeters on the market.
The display is fully programmable to show you your live and max Voltage, Amperage, Wattage Temperatures, RPM, mAH used, and more! Since you can know your mAH after your session, you know approximately how much juice is left in your pack!
Just connect it after your session for readback of live and max data. Or, since the PowerPanel is so
light, it can easily be attached to
the side of your model for live/max display all the time!
Click here for detailed specifications, and links to online instruction manuals.
Click hereto read reviews of the eLogger and PowerPanel.
eLogger V4 with with
Wire Leads, 70 Volts, 100 Amps (MPRV4-LEADS-100)
Price: $69.99
eLogger V4 with with
Wire Leads, 70 Volts, 150 Amps (MPRV4-LEADS-150)
Price: $89.99
PowerPanel LCD Display for all eLogger versions
Price: $39.99
Windows Virtual Dashboard
Windows Graphing
GPS with Google Earth and Google Track
eLogger with PowerPanel
PowerPanel
PowerPanel Top View
Sensors and Accessories for your eLogger
NEW:Video OSD Pro Expander (ETS-OSD-PRO)
Fly or race with video? The Eagle Tree OSD Pro Expander provides easy to display real time model data over your existing video link. Click here for details
Price: 89.99
NEW:Altimeter MicroSensor V4 (ALTIMETER-V4)
This sensor measures altitude with approximately 1 foot (0.3 meter) resolution. And, it runs standalone as a Max Altitude display sensor as well as connecting to the eLogger, or with our OSD Products! Click here for details.
Price: $37.99
NEW: 3-Axis G-Force Microsensors
Need to know how many G's you pulled in that last barrel roll? Eagle Tree is pleased to offer the world's first standalone G-Force meters for RC models.
The low G sensor measures up to 8g (at least 7g) in each of the 3 axes. The high G sensor measures up to 40g (at least 38g) in the X and Y axes, and up to 8g in the Z axis.
The sensors run standalone as a Max G-Force display sensors, as well as connecting to the eLogger, or with our OSD Products! Click here for details
3-Axis 7G MicroSensor
Price: $26.99
3-Axis 38G MicroSensor
Price: $63.99
Airspeed MicroSensor V3 (AIRSPEED-V3)
This sensor measures airspeed from approximately 2 MPH to 350 MPH. And, it runs completely standalone as a Max display sensor as well as connected to the eLogger, or with our OSD Products! Includes Pitot tube. Click here for details.
Price: $42.99
Brushless Motor RPM Sensor V2 (RPM-BRS-V2) Tiny sensor measures RPM by simply connecting a wire from one of your brushless electric motor leads to the sensor. Click here for instruction manual.
Price: $14.99
10Hz GPS Expander Module (GPS-V4) New GPS Expander Module based on the latest GPS technology. Built-in LED which indicates 3D fix.
Our software lets you view your recorded GPS data in Google EarthTM and Google Earth TrackTM!
Fast 10Hz update rate. Built-in battery backup for quick fixes. Integrated toroid and onboard filtering greatly reduces the affect of RFI from your FPV video transmitter.
Plugs into the eLogger V4 or V3 to provide live and/or recorded lat/lon, ground speed,
GPS altitude, distance to pilot, course, UTC timestamp, and
more. Integrated display/3D graphing software
included in data system. WAAS and EGNOS compatible, built-in patch antenna.
NOTE: if you plan to use the GPS with your eLogger with 8S (approximately 30V) packs or higher, the Battery Backup Harness (CAB-BAT-BACK) below is required. Click
Here to view Instruction Manual
Price: $79.99
Servo Current Monitor (SERVO-CURR-LOG)
Find out how much current one or more of your servos or other low current devices are drawing. Plugs into your eLogger and servo (or receiver battery/BEC) to log current from 0-5 Amps continuous, with 0.01 Amp resolution. Click here for details.
Price: $24.99
Micro Temp Sensor(TEMP-MICRO)
Perfect
for measuring temps of your batteries and ESC. 250
degrees F max temp.
Up to three temperature sensors can be connected to the eLogger V4 or V3 simultaneously (two simultaneously for the V1/V2).
Price: $9.99
Temperature Sensor (TEMP-LOOP)
Loop-around temperature sensor measures temp up to 420 degrees
F. Great for looping around motors.
NEW: Up to three temperature sensors can be connected to the eLogger V4 or V3 simultaneously (two simultaneously for the V1/V2).
Price: $9.99
Hall Effects RPM Sensor with 4 magnets (RPM-KIT-MAG)
Measures RPM to 50K+.
See the eLogger Instruction manual for details on how to use the Hall RPM Sensor.
Price: $9.99
NEW:Spektrum/JR (TM) Interface Cable (CAB-SPEK) Now use your eLogger V4 or V3 to see Spektrum/ JR Rx holds/failsafes, lost frames, and antenna fades (up to 4 antennas) on your PowerPanel, or logged for later review!
Connects between your Spektrum "FlightLog" data port and the eLogger V4 or V3's GPS port. Use a servo Y cable to use your FlightLog display simultaneously! NOTES: make sure your RX has the data port before ordering. Also, note that this cable cannot presently be used at the same time as our GPS module!Click
Here to view Instruction Manual
Price: $4.99
Optical RPM Sensor For eLogger V4, V3 & V2 (OPT-RPM)
Meeasures
your RPM without need for installing magnets. Note: This version is for the eLogger V4, V3 and the V2, which we have been selling since early 2006. The eLogger V2 has the large white letters "V2" (or "U2") on the bottom of the circuit board, near the RPM/Temp pins. Click
here for instruction manual. If you are not sure what eLogger version you have, order this optical sensor.
Price: $14.99
Custom Y Cable for Throttle Logging (CAB-Y-1)
Monitor Throttle or other servo movements with your eLogger V4 or V3! Note: this cable is included with the eLogger V4.
Price: $7.99
NEW:RCA to Servo Connector Adapter Cable for OSD Expander
Useful if your video equipment uses RCA plugs. Two are needed if both your camera and video transmitter use RCA.
Price: $9.99
External Active Antenna for GPS Expander Module (GPS-ANT) This tiny external antenna is great if you need to mount your GPS Expander under carbon fiber, or in other "RF challenging" locations. The Expander will pick between the strongest of the two signals (from the built-in antenna or this External Antenna) which can improve reception if your model is upside down, etc. Includes cable with MMCX jack. NOTE: the antenna is NOT compatible with our older GPS modules, or our new GPS-V4 module. These do not have the gold MMCX external antenna connector!
Price: $24.99
RPM or Temperature Extension Cable (CAB-RPM-EXT)
12” (30 cm) 3 pin extension cable for our RPM and Temperature sensors
Price $4.99
Bag of 10 RPM Magnets (MAGNETS)
Extra Magnets for the Hall Effects RPM Sensor.
Price $9.99
Battery Backup Harness (CAB-BAT-BACK)
Lets you power your eLogger V3 from a separate backup battery (4.8v - 6v) if your primary pack dips below about 4.5 v. Note that the eLogger will correctly log the voltage of your primary pack even when the Backup Harness is used. Click here for instruction manua.l Note: the eLogger V4 uses the included servo Y cable for backup power.
Price $4.99
PowerPanel/MicroSensor/GPS Extension Cable (CAB-EXP-EXT)
12” (30 cm) 4 pin extension cable for the the PowerPanel and MicroSensors.
Price $4.99
Replacement Custom USB Cable(USB-CABLE)
Extra 1 meter (approx 3') long USB cable
Price $9.99
T-Fitting (PITOT-T-FITTING)
Small plastic Tee fitting for sharing the static source of the pitot tube with both altimeter and airspeed static inputs.
$1.99
Snap-on Ferrite Choke (CHOKE-FERRITE)
Useful for suppressing RF from noisy video camera or other leads. Weight 0.4 oz. One will snap around several adjacent cables.